Black Box Computer Hardware ACS251A R2 User Manual

THE SERVSWITCH FAMILY  
Welcome to the ServSwitch Family!  
®
Thank you for purchasing a BLACK BOX ServSwitch Brand KVM Extender  
model! We appreciate your business, and we think you’ll appreciate the many ways  
that your enhanced keyboard/video/mouse system will save you money, time, and  
effort.  
That’s because our ServSwitch family is all about breaking away from the  
traditional, expensive model of computer management. You know, the one-size-  
fits-all-even-if-it-doesn’t model that says, “One computer gets one user station, no  
more, no less.” Why not a single user station (monitor, keyboard, and mouse) for  
multiple computers—even computers of different platforms? Why not a pair of  
user stations, each of which can control multiple computers? Why not multiple  
user stations for the same computer?  
With our ServSwitch products, there’s no reason why not. We carry a broad line  
of robust solutions for all these applications. Do you have just two PCs, and need  
an economical alternative to keeping two monitors, keyboards, and mice on your  
®
desk? Or do you need to share dozens of computers, including a mix of IBM PC,  
®
®
®
®
®
RS/6000 , Apple Macintosh , Sun Microsystems , and SGI™ compatibles among  
multiple users with different access levels? Does your switch have to sit solidly on a  
worktable and use regular everyday cables? Or does it have to be mounted in an  
equipment rack and use convenient many-to-one cables? No matter how large or  
small your setup is, no matter how simple or how complex, we’re confident we  
have a ServSwitch system that’s just right for you.  
The ServSwitch family from Black Box—the one-stop answer for all your KVM-  
switching needs!  
*
This manual will tell you all about your new ServSwitch Brand Fiber KVM  
Extender II or II-SM, including how to install, operate, and troubleshoot it. For an  
introduction to the extender, see Chapter 2. The extender product codes covered  
in this manual are:  
ACS250A-R2  
ACS251A-R2  
1
FCC AND IC RFI STATEMENTS  
FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA  
RADIO-FREQUENCY INTERFERENCE STATEMENTS  
This equipment generates, uses, and can radiate radio-frequency energy, and if not  
installed and used properly, that is, in strict accordance with the manufacturer’s  
instructions, may cause interference to radio communication. It has been tested  
and found to comply with the limits for a Class A computing device in accordance  
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to  
provide reasonable protection against such interference when the equipment is  
operated in a commercial environment. Operation of this equipment in a  
residential area is likely to cause interference, in which case the user at his own  
expense will be required to take whatever measures may be necessary to correct the  
interference.  
Changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
This digital apparatus does not exceed the Class A limits for radio noise emission from digital  
apparatus set out in the Radio Interference Regulation of Industry Canada.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites  
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le  
brouillage radioélectrique publié par Industrie Canada.  
3
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
EUROPEAN UNION DECLARATION OF CONFORMITY  
This is to certify that, when installed and used according to the instructions in this  
manual together with the specified cables, the ServSwitch Brand Fiber KVM  
Extender II and II-SM are shielded against the generation of radio interference in  
accordance with the application of Council Directive 89/336/EEC.  
The extenders were tested in a typical configuration.  
LASER-SAFETY STATEMENT  
To meet laser-safety requirements, the extender operates its optical transceivers  
within their maximum ratings. The transceivers must always be terminated with an  
optical connector or dust cap. For full optical specifications, see Chapter 1.  
CAUTION!  
Using lenses, magnifying glasses, or other optical instruments with this  
product could pose extreme eye hazards. All necessary adjustments  
have already been made at the factory prior to the shipment of the  
extender. Even if it doesn’t result in damage or injury (which is likely),  
tampering with or modifying the extender, or changing the way it  
performs, could void the extender’s original certifications.  
4
NOM STATEMENT  
NORMAS OFICIALES MEXICANAS (NOM)  
ELECTRICAL SAFETY STATEMENT  
INSTRUCCIONES DE SEGURIDAD  
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de  
que el aparato eléctrico sea operado.  
2. Las instrucciones de seguridad y operación deberán ser guardadas para  
referencia futura.  
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de  
operación deben ser respetadas.  
4. Todas las instrucciones de operación y uso deben ser seguidas.  
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca  
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.  
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que  
sean recomendados por el fabricante.  
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea  
recomendado por el fabricante.  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá  
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser  
referido a personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no  
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,  
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar  
en libreros o gabinetes que impidan el flujo de aire por los orificios de  
ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor  
como radiadores, registros de calor, estufas u otros aparatos (incluyendo  
amplificadores) que producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del  
tipo descrito en el instructivo de operación, o como se indique en el aparato.  
5
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización  
del equipo no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no  
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,  
poniendo particular atención a los contactos y receptáculos donde salen del  
aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las  
recomendaciones del fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas  
de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea  
usado por un largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean  
derramados sobre la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su  
desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
6
CONTENTS  
Contents  
Chapter  
Page  
1. Specifications ........................................................................................ 8  
2. Introduction ........................................................................................ 11  
2.1 Overview ....................................................................................... 11  
2.2 Key Features ................................................................................. 12  
2.3 The Complete Package ............................................................... 12  
3. Compatibility and Signal Processing ................................................. 13  
3.1 Video Processing ........................................................................... 13  
3.2 Mouse Compatibility .................................................................... 14  
3.3 Sound Processing ......................................................................... 15  
4. Installation .......................................................................................... 16  
4.1 Guidelines and Limitations for Attaching Equipment .............. 16  
4.1.1 CPU ..................................................................................... 16  
4.1.2 Monitor ............................................................................... 16  
4.1.3 Keyboard and Mouse ......................................................... 16  
4.2 An Extender Installation Illustrated ........................................... 17  
4.3 Installing the Local Unit and Local Devices .............................. 18  
4.4 Installing the Remote Unit and Remote Devices ...................... 20  
4.5 Finishing Your Installation .......................................................... 22  
5. Operation ............................................................................................ 23  
6. Troubleshooting ................................................................................. 24  
6.1 Calling Black Box .......................................................................... 24  
6.2 Shipping and Packaging .............................................................. 24  
7
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
1. Specifications  
Cable Required: ACS250A-R2: 50/125-µm or (to lesser distances) 62.5/  
125-µm multimode duplex fiberoptic cable;  
ACS251A-R2: 9/125-µm single-mode duplex fiberoptic  
cable  
Compliance:  
Interfaces:  
CE; FCC Part 15 Subpart B Class A, IC Class/classe A  
Extension:  
ACS250A-R2: Duplex multimode fiberoptic;  
ACS251A-R2: Duplex single-mode fiberoptic;  
Video: VGA compatible (DOS mode, VGA, SVGA, XGA,  
SXGA, UXGA); Plug-and-play for monitors and DDC is  
supported;  
Keyboard and mouse: IBM PS/2 compatible;  
Sound: 3.5-mm mono audio  
Resolution and  
Refresh Rate:  
Supports resolutions up to 1600 x 1200 and refresh rates at  
75 Hz; maximum pixel clock (bandwidth) is 108 MHz  
Optical Type and  
Wavelength:  
ACS250A-R2: 850-nm multimode;  
ACS251A-R2: 1300-nm single-mode  
Transmitter  
Launch Power:  
ACS250A-R2: Into either 50-µm or 62.5-µm cable: From -4.5  
to -9 dBm;  
ACS251A-R2: Into 9-µm cable: From -3 to -9 dBm  
Receiver  
Sensitivity:  
ACS250A-R2:  
With 62.5-µm cable: -12.5 dBm;  
With 50-µm cable: -13.5 dBm;  
ACS251A-R2: -14.4 dBm  
Optical  
Budget:  
ACS250A-R2:  
With 62.5-µm cable: 6.7 dB maximum;  
With 50-µm cable: 7.5 dB maximum;  
ACS251A-R2: 10.5 dB maximum  
8
CHAPTER 1: Specifications  
Maximum  
Distance:  
Between extender’s local and remote units:  
ACS250A-R2:  
Over 62.5-µm cable: 720 ft. (219.5 m);  
Over 50-µm cable: 1310 ft. (399.3 m);  
ACS251A-R2: 6.2 mi. (10 km)  
User Controls:  
Connectors:  
None  
On local unit:  
Front-mounted:  
(4) 6-pin mini-DIN female:  
(1) for CPU’s keyboard port;  
(1) for CPU’s mouse port;  
(1) for optional local keyboard;  
(1) for optional local mouse;  
(1) HD15 female for CPU’s video port;  
(1) HD15 female for optional local monitor;  
(1) 3.5-mm stereo audio jack (~0.7 V /~2 Vpp) for  
eff  
CPU’s audio-out port;  
Rear-mounted:  
(1) Duplex SC female for fiber link (transmitter on  
left, receiver on right);  
(1) 2.1-mm barrel jack for power;  
(1) 8-pin mini-DIN for service (reserved for  
manufacturer use);  
On remote unit:  
Front-mounted:  
(2) 6-pin mini-DIN female:  
(1) for remote keyboard;  
(1) for remote mouse;  
(1) HD15 female for remote monitor;  
(1) 3.5-mm stereo audio jack (~0.7 V /~2 Vpp) for  
eff  
remote audio device (outputs mono on both stereo  
channels);  
Rear-mounted:  
(1) Duplex SC female for fiber link (transmitter on  
left, receiver on right);  
(1) 2.1-mm barrel jack for power;  
(1) 8-pin mini-DIN for service (reserved for  
manufacturer use)  
9
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
Indicators:  
(1) Front-mounted green LED on each unit:  
Local unit: LED is steadily lit during normal operation,  
flashes if unit is powered but no video signal is present  
at VGA input;  
Remote unit: LED is steadily lit during normal operation,  
flashes if no fiber connection is detected or local unit is  
outputting no signal  
Temperature  
Tolerance:  
Operating: 50 to 104˚ F (10 to 40˚ C);  
Storage: 32 to 158˚ F (0 to 70˚ C)  
Humidity  
Tolerance:  
Up to 70% noncondensing  
Aluminum, powder-coated  
Enclosure:  
Power:  
From utility-power (mains) outlet, through detachable  
input cord and IEC 320 male inlet to external  
transformer:  
Input: 90 to 264 VAC, 47 to 63 Hz, autosensing, at up to  
~200 mA at 115 VAC or ~100 mA at 230 VAC;  
Maximum inrush current: 40 amps;  
Output: 12 VDC at up to 2 amps (local unit draws only 1  
amp maximum, remote unit only 1.1 amps);  
Consumption:  
Local unit: 8.7 watts maximum;  
Remote unit: 9 watts maximum  
Size:  
Each unit: 2.6"H x 7.3"W x 7.1"D (6.6 x 18.5 x 18 cm)  
Weight:  
Net, local unit: 2.4 lb. (1.1 kg);  
Net, remote unit: 2.2 lb. (1 kg);  
Shipping: Approximately 10 lb. (4.5 kg)  
10  
CHAPTER 2: Introduction  
2. Introduction  
2.1 Overview  
There are many KVM extenders available, but until now many of them have used  
analog image transmission, which inherently degrades image quality (especially  
over long distances and at high video resolutions).  
The ServSwitch Brand Fiber KVM Extender II and II-SM is a digital image-  
transmission system. Video output from a local computer CPU is automatically  
digitized by the extender’s local unit and transmitted serially to the remote unit on  
a single fiber at data rates up to 1.5 Gbps. The remote unit converts the digital  
signal back into the original analog signal. Up to the maximum specified cable  
lengths, image quality is independent of cable length.  
The extender uses its second fiber to send remote mouse and keyboard  
information back to the local CPU. The extender needs only these two fibers for  
full operation. Compared with some analog KVM extenders that require as many  
as five fibers, the Fiber KVM Extender II and II-SM can save you significant  
amounts of money, especially if you’ll need to run fiber cable across long distances.  
There are two models of the extender:  
• The Fiber KVM Extender II (ACS250A-R2) is the multimode model. It  
transmits digital video up to 720 ft. (219.5 m) across 62.5/125-µm multimode  
fiber or up to 1310 ft. (399.3 m) across 50/125-µm multimode fiber.  
• The Fiber KVM Extender II-SM (ACS251A-R2) is the single-mode model. It  
transmits digital video up to 6.2 mi. (10 km) across 9/125-µm single-mode fiber.  
In addition to the keyboard, video, and mouse information, the local unit can also  
digitize optional sound information from a local CPU or other audio device and  
encode it into the digital information sent to the remote unit on the video fiber.  
The sound quality won’t approach high fidelity (it will be converted to monaural if  
it’s stereo), but will be roughly equivalent to that of sound transmitted over the  
telephone, which is sufficient for error messages and so forth.  
You can also connect an optional local user station (keyboard, monitor, and  
mouse only) to the local unit. The local unit will pass video through to the local  
monitor and will switch the keyboard and mouse. (This means that the local user  
contends with the remote user for keyboard and mouse control of the CPU: Once  
the active user station is idle for 2 seconds, the first user to type at the keyboard or  
move the mouse will be granted control.)  
11  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
2.2 Key Features  
• Digital transmission of video, keyboard, mouse, and optional audio  
information on only two fibers over distances up to 1310 ft. (399.3 m) of  
multimode cable or 6.2 mi. (10 km) of single-mode cable.  
• Supports an optional local monitor, keyboard, and mouse user station that  
contends with the remote station for CPU control.  
• Supports several of the most common VGA-compatible video standards (DOS  
mode, VGA, XGA, SVGA, SXGA, or UXGA) at resolutions up to 1600 x 1200  
or output refresh rates up to 75 Hz.  
• Automatic adjustment of all transmission and image parameters—you don’t  
have to configure it.  
• All cables you would normally need except for the fiber cable are included.  
2.3 The Complete Package  
At the time of this writing, your extender package should consist of:  
• The extender’s local unit.  
• The extender’s remote unit.  
• (2) Power supplies with 6-ft. (1.8-m) nondetachable output cords, one for each  
unit.  
• (2) Input cords, one for each power supply; length might vary depending on  
region and source, but is normally 6 ft. (1.8 m).  
• (1) 6-ft. (1.8-m) VGA-extension cable with HD15 male connectors at both  
ends.  
®
• (2) 6.6-ft. (2-m) PS/2 extension cables with 6-pin mini-DIN male connectors  
at both ends.  
• (1) 6.6-ft. (2-m) audio-extension cable with 3.5-mm stereo audio plugs at both  
ends.  
• This manual.  
However, the package contents are subject to change without notice. If the  
package has been damaged, contact both Black Box and the shipping carrier.  
12  
CHAPTER 3: Compatibility and Signal Processing  
3. Compatibility and  
Signal Processing  
This chapter discusses technical details of how the ServSwitch Brand Fiber KVM  
Extender II and II-SM process I/O signals, and how that processing affects  
compatibility with various equipment.  
3.1 Video Processing  
The extender’s local unit contains powerful electronics to process your video signal  
with superior quality. Video input is digitized as 16-bit data (65,536 colors). The  
local unit can accept these resolutions and vertical refresh rates (though the refresh  
rate output by the remote unit is always 60, 75, or 85 Hz):  
• DOS mode at 640 x 400, 720 x 400, 640 x 350, or 720 x 350 at up to 85 Hz  
• VGA 640 x 480 at up to 85 Hz  
• SVGA 800 x 600 at up to 85 Hz  
• XGA 1024 x 768 at up to 75 Hz  
• VGA-compatible 1152 x 864 at up to 75 Hz  
• SXGA 1280 x 1024 at up to 72 Hz  
• UXGA 1600 x 1200 at 60 Hz  
It also accepts these synchronization options (though the remote unit always  
outputs separate horizontal and vertical sync):  
• Separate horizontal and vertical sync (RGBHV), common on PCs.  
• Composite sync on the horizontal sync line (RGBS), used in some older  
machine-control systems.  
• Composite sync overlaid on the green color signal (RGsB, “sync on green”),  
®
common on many UNIX workstations.  
Almost all non-DDC signals that might be received from the attached computer  
CPU at the “CPU Video” connector are passed through to the “Local Video”  
connector for the optional local monitor. These signals are buffered internally for  
better signal integrity.  
13  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
The brightness and contrast of the video signal are adjusted automatically before  
digitizing the signal. This ensures the best possible video quality without requiring  
configuration or adjustment by the user.  
When the local unit detects that the CPU has switched to a different resolution,  
refresh rate, etc., it will adjust all digitizing parameters automatically. Only a few  
seconds later, you will again have a sharp, crisp, and colorful image without having  
to move any switches or turn any dials. The local unit checks all video parameters  
continuously, so video quality is maximized at all times.  
After the local unit digitizes the video, it transmits the digital data across the  
fiber as a serial stream. Inside the remote unit, the signal is converted back into the  
original analog values, which it outputs from its “Video” connector. The resolution  
of the output signal is always the same as that of the original input, but its vertical  
refresh rate is kept constant (by dropping or repeating frames). No matter what  
their input refresh rate is:  
• DOS-mode resolutions will be output at a refresh rate of 85 Hz.  
• Non-DOS-mode resolutions up to 1152 x 864 will be output at a refresh rate of  
75 Hz.  
• 1280 x 1024 and 1600 x 1200 resolution will be output at a refresh rate  
of 60 Hz.  
Make sure that the remote monitor can support your chosen resolution at the  
corresponding rate. If it doesn’t, the display will look bad or be totally blank.  
The remote unit will always output separate horizontal and vertical sync from its  
“Video” connector on the standard VGA Hsync and Vsync pins (HD15 pins 13 and  
14). If you need to connect a remote monitor that uses some other type of sync  
and/or separate BNC connectors rather than an HD15 VGA connector, call Black  
Box Technical Support for assistance.  
The local unit will support DDC (display data channel) and provide information to  
the local workstation about its video capabilities. Modern workstations will evaluate  
this information and set up their graphics output according to the supported  
resolutions of the extender.  
3.2 Mouse Compatibility  
The extender supports all common PS/2 style mice and pointing devices including  
®
two-button mice, three-button mice, wheel mice such as the Microsoft  
IntelliMouse , trackballs, etc.  
®
14  
CHAPTER 3: Compatibility and Signal Processing  
3.3 Sound Processing  
The local unit receives stereo sound input and converts it into a monaural “sum”  
signal. (The local unit supports standard input-signal levels of 0.7 V [effective  
eff  
volts], equivalent to about 2 Vpp [volts peak-to-peak].) This signal is then digitized  
as 8-bit data by sampling at a rate of about 16 kHz. The remote unit converts the  
signal back to analog audio and outputs the monaural sound simultaneously on  
both the left and right stereo channels. You can adjust the volume using the  
volume controls of your active speakers or other audio-output devices and/or your  
CPU’s operating system.  
15  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
4. Installation  
4.1 Guidelines and Limitations for Attaching Equipment  
This section discusses a few things you need to keep in mind about the types of  
devices you can attach to a ServSwitch Brand Fiber KVM Extender II or II-SM, in  
addition to those described in Chapter 3.  
4.1.1 CPU  
®
The extender supports IBM PC compatible computer CPUs. A CPU must have  
these kinds of interfaces to work properly with the extender:  
Video: VGA compatible (DOS mode, VGA, SVGA, XGA, SXGA, or UXGA),  
outputting resolutions and refresh rates such as:  
– 1600 x 1200 at 60 Hz;  
– 1280 x 1024 at up to 72 Hz;  
– 1152 x 864 or 1024 x 768 at up to 75 Hz; or  
– 800 x 600 or lower at 85 Hz.  
Keyboard: IBM PS/2 style (6-pin mini-DIN). (With a keyboard-port adapter, will  
®
also support CPUs with PC/AT [5-pin DIN] keyboard ports.)  
Mouse: IBM PS/2 style (6-pin mini-DIN).  
4.1.2 MONITOR  
Any monitor you attach to the extender needs to be able to display a VGA  
compatible video signal (VGA, SVGA, XGA, SXGA, or UXGA) at the resolution and  
refresh rate that your CPU is outputting it (see Section 4.1.1). If you use a plug-  
and-play or DDC monitor (at either the local or remote station), you’ll have to  
configure its video settings manually, because the extender can’t carry the DDC  
signals or the plug-and-play identification/negotiation signaling. When you do this,  
make sure to choose only those settings that your monitor can support (refer to  
the monitor’s manual). Configuring video incorrectly, especially if you select  
refresh rates that are too high for the monitor to display, could damage or destroy  
the monitor.  
4.1.3 KEYBOARD AND MOUSE  
The extender’s keyboard and mouse interfaces are standard PS/2 type interfaces,  
so you can attach just about any standard PS/2 compatible keyboard and mouse to  
the extender. Do not attach serial mice or bus mice to the extender; they will not  
work. You can attach a PC/AT style keyboard with a 5-pin DIN connector to the  
extender by using a keyboard adapter, available separately as product code FA211-R2.  
16  
CHAPTER 4: Installation  
4.2 An Extender Installation Illustrated  
Figure 4-1 shows where to attach your devices in a typical ServSwitch Brand Fiber  
KVM Extender II or II-SM system installation. (The front panels of the extenders  
are shown here; the SC fiber connectors will be on their rear panels.) Refer to this  
illustration as you follow the instructions in the rest of this chapter.  
Active  
speakers  
(optional)  
Remote  
monitor,  
keyboard,  
and mouse  
Extender  
remote unit  
Duplex fiber cabling  
with SC connectors  
Extender  
local unit  
Audio-  
extension  
cable  
(optional,  
included)  
Local monitor, keyboard,  
and mouse (optional)  
VGA and PS/2 extension  
cables (included)  
Figure 4-1. How to install an extender system.  
17  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
4.3 Installing the Local Unit and Local Devices  
Place the local unit on a flat surface within about 10 ft. (3 m) of a working AC  
outlet and 6 ft. (1.8 m) of your local CPU and any local user-station equipment.  
NOTE  
It is also possible to rackmount the local and remote units, but it  
requires additional hardware. Call Black Box Technical Support if you  
would like to do this.  
Making sure that your computer CPU and any other local equipment is powered  
off, attach it to the CPU-port connectors on the local unit’s front panel using the  
extender’s included cables:  
• Run the included VGA-extension cable from the CPU’s video port to the local  
unit’s HD15 female connector labeled “CPU Video.”  
• Run one of the included PS/2 extension cables from the CPU’s keyboard port  
to the local unit’s 6-pin mini-DIN female connector labeled with the word  
“CPU” and a keyboard icon. (If the CPU has a 5-pin DIN PC/AT style  
keyboard port, use an FA212 keyboard-port adapter at the CPU end.)  
• Run the other included PS/2 extension cable from the CPU’s mouse port to  
the local unit’s 6-pin mini-DIN female connector labeled with the word “CPU”  
and a mouse icon.  
Optional: Run the included audio-extension cable from the “audio out” port of  
the CPU or some other device to the local unit’s 3.5-mm mono audio jack  
labeled “Sound.”  
If you want to attach an optional local user station, plug the devices directly into  
the user-port connectors on the local unit’s front panel:  
• Plug any local monitor into the local unit’s HD15 female connector labeled  
“Local Video.” Note that the extender has no support for DDC or monitor  
plug-and-play, so you’ll have to configure its video settings manually through  
the CPU’s operating system. When you do this, make sure to choose only those  
settings that your monitor can support (refer to the monitor’s manual).  
Configuring video incorrectly, especially if you select refresh rates that are too  
high for the monitor to display, could damage or destroy the monitor.  
• Plug any local keyboard into the local unit’s 6-pin mini-DIN female connector  
labeled with the word “Local” and a keyboard icon. If the keyboard has a 5-pin  
DIN PC/AT style connector, use an FA211-R2 keyboard adapter.  
18  
CHAPTER 4: Installation  
• Plug any local mouse into the local unit’s 6-pin mini-DIN female connector  
labeled with the word “Local” and a mouse icon.  
Make a last pair of attachments to the connectors on the local unit’s rear panel:  
• Attach the SC male connectors at the local-unit end of your duplex fiber  
cabling to the local unit’s SC female connectors. (The extender’s SC  
connectors are keyed so that you can’t plug the fiber cable in the wrong way.)  
Make sure that this fiber cabling, from here all the way to the remote unit, is  
either 62.5/125-µm or 50/125-µm multimode type for the Extender II  
(ACS250A-R2) or is 9/125-µm single-mode type for the Extender II-SM  
(ACS251A-R2). It can either be a single cable that will run all the way to the  
remote unit or a patch cable that will run to your fiber-distribution closet. Just  
keep in mind that the more fiber connectors the extender’s optical signal runs  
through, the more it attenuates.  
• Plug the output cord of one of the extender’s included power supplies into the  
2.1-mm barrel jack on the local unit’s rear panel. (The two power supplies are  
identical, so you can use either one.) Attach the female end of the power  
supply’s input cord to the IEC 320 male inlet on the transformer. Plug the  
other end of the input cord into a working AC outlet. The local unit should  
power up immediately—it has no ON/OFF switch. The green Status LED on  
its front panel should begin flashing to show that it isn’t getting a video signal  
from the CPU yet.  
Don’t power up the attached devices yet—wait until you’re ready to test the  
system after installing the remote unit and remote equipment.  
CAUTION!  
Do not attach anything to the 8-pin mini-DIN connector labeled  
“Service” on the local unit’s rear panel, which is reserved for  
manufacturer use. Doing so could severely damage the extender and  
any attached equipment!  
19  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
4.4 Installing the Remote Unit and Remote Devices  
Place the remote unit on a flat surface (or rackmount it—see the Note on page 17)  
within about 10 ft. (3 m) of a working AC outlet and 6 ft. (1.8 m) of your remote  
user-station equipment. Making sure that your remote equipment is powered off,  
plug it directly into the user-port connectors on the extender’s front panel:  
• Plug the remote monitor into the remote unit’s HD15 female connector  
labeled “Video.” Note that the extender has no support for DDC or monitor  
plug-and-play. It also outputs fixed refresh rates for various resolutions (60 Hz  
for 1600 x 1200 and 1280 x 1024, 75 Hz for all other non-DOS-mode  
resolutions up to 1152 x 864, and 85 Hz for all DOS-mode resolutions.) For  
whichever resolution(s) your CPU outputs, make sure to connect only a  
monitor that can support that resolution at the extender’s corresponding  
refresh rate. If a monitor attempts to display a refresh rate too high for it to  
support, the monitor could be damaged or destroyed.  
• Plug the remote keyboard into the remote unit’s 6-pin mini-DIN female  
connector labeled with a keyboard icon. If the keyboard has a 5-pin DIN  
PC/AT style connector, use an FA211-R2 keyboard adapter.  
• Plug the remote mouse into the remote unit’s 6-pin mini-DIN female  
connector labeled with a mouse icon.  
Optional: Plug active speakers or some other type of powered audio-receiving  
device into the remote unit’s 3.5-mm audio jack labeled “Sound.” (Use only  
active speakers; the drive level of the remote unit is not high enough to  
operate passive speakers. It is theoretically possible to attach headphones, but  
their volume will not be adjustable except through the CPU.) If the device  
doesn’t have an attached audio cable, you’ll need to run an audio-extension  
cable (not included) between it and the remote unit. Adjust the volume of  
your speakers or other device with the device’s own volume controls and/or  
the volume control for audio output in the CPU’s operating system. (Keep in  
mind that even if the input is stereo, the output will always be monaural.)  
20  
CHAPTER 4: Installation  
Make a last pair of attachments to the connectors on the remote unit’s rear panel:  
• Attach the SC male connectors at the remote-unit end of your duplex fiber  
cabling to the remote unit’s SC female connectors. (The extender’s SC  
connectors are keyed so that you can’t plug the fiber cable in the wrong way.)  
• Plug the output cord of the extender’s second included power supply into the  
2.1-mm barrel jack on the remote unit’s rear panel. Attach the outlet end of  
the power supply’s input cord to the IEC 320 male inlet on the transformer.  
Plug the other end of the input cord into a working AC outlet. The local unit  
should power up immediately—it has no ON/OFF switch. The green Status  
LED on its front panel should begin flashing to show that it isn’t getting a  
video signal from the local unit yet.  
CAUTION!  
Do not attach anything to the 8-pin mini-DIN connector labeled  
“Service” on the local unit’s rear panel, which is reserved for  
manufacturer use. Doing so could severely damage the extender and  
any attached equipment!  
21  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
4.5 Finishing Your Installation  
To complete your extender installation and begin operating the system, plug in  
and turn on the remote monitor. A gray box should appear on the screen with the  
words “NO SIGNAL” in it. (If you see a red box that says “NO FIBER LINK”  
instead, make sure that the fiber cabling is securely connected and intact from end  
to end and that the local unit is receiving power.) Plug in and turn on any powered  
remote speakers or other audio devices. Have someone at the local site (where the  
local unit is) plug in and turn on the local monitor if you’ve installed one; the local  
monitor should be blank or turn its power-save feature on. Lastly, have that person  
boot the CPU.  
The extender should automatically detect and adapt to the type, resolution,  
refresh rate, brightness, and contrast of the video signal sent by the CPU, and  
begin displaying video within a few seconds. The Status LEDs on the local and  
remote units should change from flashing to steadily lit. You can watch the CPU’s  
bootup process while it’s displayed at the remote site; if you have a local monitor  
installed, the person at the local site can watch the bootup process there. Make  
sure video is transmitted and displayed properly. If you’re sending audio through  
the extender, make sure that’s getting through as well. (It will be monaural and  
might not sound great, but it should approach telephone quality.)  
Make sure that keyboard and mouse control from the remote site works OK. If  
you have a local keyboard and monitor installed, the person at the local site should  
make sure that they also work, and the two of you should quickly check contention  
(after two idle seconds, the user at either keyboard and mouse should be able to  
take over control of the CPU from the other).  
If any signals are failing to get through to any of your devices, check all of the  
involved cabling and make sure that it’s the correct type, isn’t broken or run too  
far, and is securely attached at all connectors. If this doesn’t help, call Black Box  
Technical Support as described in Chapter 6.  
If everything works OK, your ServSwitch Brand Fiber KVM Extender II or II-SM  
system should be completely installed and ready for continuous operation without  
requiring further human intervention.  
22  
CHAPTER 5: Operation  
5. Operation  
Once the ServSwitch Brand Fiber KVM Extender II or II-SM is installed and  
powered, it will perform keyboard/video/mouse extension to the remote site  
continuously. It will also perform ongoing keyboard/mouse switching if you have  
both local and remote user stations attached. The extender will display these  
indications:  
• The Status LED on the front of the local unit will be steadily lit during normal  
operation; it will flash if no video signal is being received from the CPU.  
• The Status LED on the front of the remote unit will be steadily lit during  
normal operation; it will flash (and “NO SIGNAL” will appear on the remote  
monitor) if no video signal is being received from the local unit. (“NO FIBER  
LINK” will appear on the remote monitor if the remote unit is unable to detect  
the presence of the local unit at all. This might happen if the local unit loses  
power or the fiber cabling is disconnected or damaged.)  
23  
SERVSWITCH™ BRAND FIBER KVM EXTENDER II AND II-SM  
6. Troubleshooting  
6.1 Calling Black Box  
If you determine that your ServSwitch Brand Fiber KVM Extender II or II-SM is  
malfunctioning, do not attempt to alter or repair the unit. It has no user-serviceable  
components. Contact Black Box Technical Support at 724-746-5500.  
Before you do, make a record of the history of the problem. We will be able to  
provide more efficient and accurate assistance if you have a complete description,  
including:  
• the nature and duration of the problem;  
• when the problem occurs;  
• the components involved in the problem—that is, what type of computer, what  
type of keyboard, brand of mouse, make and model of monitor, make and  
model of speakers or other audio devices, type and make of fiber cable, etc.;  
• any particular application that, when used, appears to create the problem or  
make it worse; and  
• the results of any testing you’ve already done.  
6.2 Shipping and Packaging  
If you need to transport or ship your extender:  
• Package it carefully. We recommend that you use the original container.  
• If you are returning the unit, include everything you received with it. Before  
you ship the unit back to Black Box for repair or return, contact us to get a  
Return Authorization (RA) number.  
24  
DISCLAIMERS  
DISCLAIMERS  
While every precaution has been taken in the preparation of this manual, neither  
the manufacturer nor its authorized agents assume any responsibility for errors or  
omissions. Nor do they assume any liability for damages resulting from the use of  
the information contained herein. They reserve the right to change the  
specifications, functions, or circuitry of the product without notice.  
Neither the manufacturer nor its authorized agents accept liability for damage  
due to misuse of the product or due to other circumstances outside their control.  
And they will not be responsible for any loss, damage, or injury arising directly or  
indirectly from the use of this product.  
25  
NOTES  
26  
NOTES  
27  
NOTES  
28  

HP Hewlett Packard HP Pavilion LED LCD Monitor 2711x User Manual
HP Hewlett Packard Hewlett Packard Computer Hardware XA User Manual
Fujitsu Siemens Computers Fujitsu Siemens Premium Line 5110 FA User Manual
Frigidaire FFEC3025LW User Manual
Electrolux Air O Convect 269020 User Manual
Cres Cor Convection Oven CO151FPWUA12B Q1 User Manual
Cannon C50GCK User Manual
Cadco Line Chef COL08 User Manual
Black Decker TRO4085C User Manual
Asus E3746 User Manual