Asus Computer Monitor VW195XL User Manual

VW195xL /  
VW202xL /  
VW225xL Series  
LCD Monitor  
User Guide  
MENU  
Contents  
iii  
 
Notices  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
This device may not cause harmful interference, and  
This device must accept any interference received including interference that  
may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy and, if not installed and used in accordance with manufacturer’s  
instructions, may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment to an outlet on a circuit different from that to which the  
receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is  
required to assure compliance with FCC regulations. Changes or modifications  
to this unit not expressly approved by the party responsible for compliance  
could void the user’s authority to operate this equipment.  
As an Energy Star® Partner, our company has determined that this product meets  
the Energy Star® guidelines for energy efficiency.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions  
from digital apparatus set out in the Radio Interference Regulations of the  
Canadian Department of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
iv  
 
TCO Development  
Congratulations!  
The display you have just purchased carries the  
TCO’03 Displays label. This means that your  
display is designed, manufactured and tested  
according to some of the strictest quality and  
environmental requirements in the world. This  
makes for a high performance product, designed  
with the user in focus that also minimizes the  
impact on our natural environment.  
Some of the features of the TCO’03 Display requirements:  
Ergonomics  
Good visual ergonomics and image quality in order to improve the working  
environment for the user and to reduce sight and strain problems. Important  
parameters are luminance, contrast, resolution, reflectance, colour rendition  
and image stability.  
Energy  
Energy-saving mode after a certain time – beneficial both for the user and the  
environment  
Electrical safety  
Emissions  
Electromagnetic fields  
Noise emissions  
Ecology  
The product must be prepared for recycling and the manufacturer must have a  
certified environmental management system such as EMAS or ISO 14 001  
Restrictions on  
- chlorinated and brominated flame retardants and polymers  
- heavy metals such as cadmium, mercury and lead.  
The requirements included in this label have been developed by TCO  
Development in cooperation with scientists, experts, users as well as  
manufacturers all over the world. Since the end of the 1980s TCO has been  
involved in influencing the development of IT equipment in a more user-friendly  
direction. Our labelling system started with displays in 1992 and is now requested  
by users and IT-manufacturers all over the world.  
v
Safety information  
Before setting up the monitor, carefully read all the documentation that came  
with the package.  
To prevent fire or shock hazard, never expose the monitor to rain or moisture.  
Never try to open the monitor cabinet. The dangerous high voltages inside the  
monitor may result in serious physical injury.  
If the power supply is broken, do not try to fix it by yourself. Contact a qualified  
service technician or your retailer.  
Before using the product, make sure all cables are correctly connected and the  
power cables are not damaged. If you detect any damage, contact your dealer  
immediately.  
Slots and openings on the back or top of the cabinet are provided for  
ventilation. Do not block these slots. Never place this product near or over a  
radiator or heat source unless proper ventilation is provided.  
The monitor should be operated only from the type of power source indicated  
on the label. If you are not sure of the type of power supply to your home,  
consult your dealer or local power company.  
Use the appropriate power plug which complies with your local power  
standard.  
Do not overload power strips and extention cords. Overloading can result in  
fire or electric shock.  
Avoid dust, humidity, and temperature extremes. Do not place the monitor in  
any area where it may become wet. Place the monitor on a stable surface.  
Unplug the unit during a lightning storm or if it will not be used for a long period  
of time. This will protect the monitor from damage due to power surges.  
Never push objects or spill liquid of any kind into the slots on the monitor  
cabinet.  
To ensure satisfactory operation, use the monitor only with UL listed  
computers which have appropriate configured receptacles marked between  
100-240V AC.  
If you encounter technical problems with the monitor, contact a qualified  
service technician or your retailer.  
This symbol of the crossed out wheeled bin indicates that the product (electrical  
and electronic equipment) should not be placed in municipal waste.  
Please check local regulations for disposal of electronic products.  
vi  
 
Care & Cleaning  
Before you lift or reposition your monitor, it is better to disconnect the cables  
and power cord. Follow the correct lifting techniques when positioning the  
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.  
Do not lift the display by the stand or the cord.  
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor  
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed  
with a cloth dampened with mild cleaner.  
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended  
for use with the LCD. Never spray cleaner directly on the screen, as it may drip  
inside the monitor and cause an electric shock.  
The following symptoms are normal with the monitor:  
The screen may flicker during the initial use due to the nature of the fluorescent  
light. Turn off the Power Switch and turn it on again to make sure that the  
flicker disappears.  
You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
When the same image is displayed for hours, an afterimage of the previous  
screen may remain after switching the image. The screen will recover slowly or  
you can turn off the Power Switch for hours.  
When the screen becomes black or flashes, or cannot work anymore, contact  
your dealer or service center to fix it. Do not repair the screen by yourself!  
Conventions used in this guide  
To make sure that you perform certain tasks properly, take note of the following  
symbols used throughout this manual.  
DANGER/WARNING: Information to prevent injury to yourself  
when trying to complete a task.  
CAUTION: Information to prevent damage to the components  
when trying to complete a task.  
IMPORTANT: Instructions that you MUST follow to complete a  
task.  
NOTE: Tips and additional information to help you complete a  
task.  
vii  
 
Where to find more information  
Refer to the following sources for additional information and for product and  
software updates.  
1.  
2.  
ASUS websites  
The ASUS websites worldwide provide updated information on ASUS  
Optional documentation  
Your product package may include optional documentation that may have  
been added by your dealer. These documents are not part of the standard  
package.  
viii  
1.1  
Welcome!  
Thank you for purchasing the ASUS® VW195xL/VW202xL/VW225xL Series LCD  
monitor!  
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and  
brighter display, plus a host of features that enhance your viewing experience.  
With these features, you can enjoy the convenience and delightful visual  
experience that the VW195xL/VW202xL/VW225xL Series brings you!  
1.2  
Package contents  
Check your VW195xL/VW202xL/VW225xL Series LCD monitor package for the  
following items:  
LCD monitor  
Monitor base  
Quick start guide  
1 x Power cord  
1 x VGA cable  
1 x DVI cable  
1 x Audio cable  
If any of the above items is damaged or missing, contact your retailer  
immediately.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
1-1  
 
1.3  
Monitor introduction  
1.3.1  
Front view  
MENU  
Base  
4
5
1
2
3
1.  
Button:  
Use this hotkey to switch from five video preset modes (Game Mode,  
Night View Mode, Scenery Mode, Standard Mode, Theater Mode) with  
SPLENDID™ Video Enhancement Technology.  
Exit the OSD menu or go back to the previous menu as the OSD menu  
is activated.  
Automatically adjust the image to its optimized position, clock, and phase  
by pressing this button for 2-4 seconds (for VGA mode only).  
2.  
Button:  
Press this button to decrease the value of the function selected or move  
left/up to the previous function.  
This is also a Volume hotkey for model with speaker or Contract hotkey  
for model without speaker.  
3.  
4.  
MENU Button:  
Press this button to enter/select the icon (function) highlighted while the  
OSD is activated.  
Button:  
Press this button to increase the value of the function selected or move  
right/down to the next fuction.  
This is also a hotkey for Brightness adjustment.  
1-2  
Chapter 1: Product introduction  
 
5.  
Power button/power indicator  
Press this button to turn the monitor on/off.  
The color definition of the power indicator is as the table below.  
Status  
Blue  
Description  
ON  
Amber  
OFF  
Standby mode  
OFF  
1.3.2  
Back view  
Stereo  
speaker  
Stereo  
speaker  
Screw holes for  
VESA Wall Mount  
Rear connectors  
Monitor base  
release button  
1
2
3
4
Rear connectors  
1.  
2.  
3.  
4.  
Audio-in port. This port connects PC audio source by the bundled audio  
cable.  
AC-IN port. This port connects the power connector from the bundled power  
cord.  
DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal  
connection.  
VGA port. This 15-pin port is for PC VGA connection.  
The VESA wall mount kit (100 mm x 100 mm) is purchased separately.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
1-3  
 
1-4  
Chapter 1: Product introduction  
2.1  
Assembling the monitor base  
To assemble the monitor base  
1.  
Have the monitor base place on a flat table.  
2.  
Connect the base with the arm according to the below drawing. A click sound  
shows that the base has been connected successfully.  
3.  
Remove the monitor height adjustment lock.  
3
2
1
The monitor height adjustment lock should NEVER be removed BEFORE you  
place the monitor VERTICALLY on a flat surface.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
2-1  
 
2.2  
Adjusting the monitor angles  
For optimal viewing, we recommend that you look at the full face of the monitor,  
then adjust the monitor to the angle that is most comfortable for you.  
Hold the base to prevent the monitor from falling when you change its angle.  
You can tilt the monitor’s from -3º to 20º, swivel from left-to-right for 45º, and lift  
the monitor’s height for about 70mm.  
-3º~20º  
45º  
45º  
0º  
2.3  
Detaching the arm/base (for VESA  
wall mount)  
The detachable arm / base of the VW195xL/VW202xL/VW225xL Series LCD  
monitor is specially designed for VESA wall mount.  
To detach the arm/base  
1.  
Lower the monitor to its lowest height, and then insert the monitor height  
adjustment lock (Figure 1).  
2.  
3.  
4.  
Have the front of the monitor face down on a table.  
Remove the rubbers in the four screw holes (Figure 2).  
Use a screwdriver to remove the two screws on the arm (Figure 2), then slide  
out the arm/base to detach it from the monitor (Figure 3).  
2-2  
Chapter 2: Setup  
 
Figure 1  
Rubbers in the  
screw holes  
Two screws  
Arm/base  
Figure 2  
Figure 3  
We recommend that you cover the table surface with soft cloth to prevent  
damage to the monitor.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
2-3  
2.4  
Disassembling the monitor base (for  
product packing)  
To disassemble the monitor base  
1.  
Lower the monitor to its lowest height, and then insert the monitor height  
adjustment lock.  
2.  
3.  
Have the front of the monitor face down on a table.  
Press and hold the release button on the monitor base and remove the  
monitor base from the monitor arm.  
3
1
2.5  
Connecting the cables  
1.  
Connect the cables as the following instructions:  
To connect the audio cable: connect one end of the audio cable to the  
monitor’s Audio-in port, the other end to the computer's audio-out port.  
To connect the power cord: connect one end of the power cord securely to  
the monitor’s AC input port, the other end to a power outlet.  
To connect the VGA/DVI cable:  
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.  
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/  
DVI port.  
c. Tighten the two screws to secure the VGA/DVI connector.  
2-4  
Chapter 2: Setup  
 
When both the VGA and the DVI cables are connected, you can choose either  
VGA mode or DVI mode from the Input Select item of the OSD functions.  
2.  
Gather all the cables with the cable hook.  
Cable hook  
2.6  
Turning on the monitor  
Gently press the power button  
button. The power indicator  
. See page 1-2 for the location of the power  
lights up in blue to show that the monitor is ON.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
2-5  
 
2-6  
Chapter 2: Setup  
3.1  
OSD (On-Screen Display) menu  
3.1.1  
How to reconfigure  
1.  
2.  
Press the MENU button to activate the  
OSD menu.  
Press  
and  
to navigate through  
the functions. Highlight and activate the  
desired function by pressing the MENU  
button. If the function selected has a  
sub-menu, press  
and  
again to  
navigate through the sub-menu functions.  
Highlight and activate the desired sub-  
menu function by pressing the MENU button.  
3.  
4.  
Press  
and  
to change the settings of the selected function.  
To exit the OSD menu, press the  
adjust any other function.  
button. Repeat step 2 and step 3 to  
3.1.2  
OSD Function Introduction  
1.  
Spendid  
This function contains five sub-functions  
you can select for your preference. Each  
mode has the Reset selection, allowing  
you to maintain your setting or return to  
the preset mode.  
Scenery Mode: best choice for  
scenery photo display with  
SPLENDID™ Video Enhancement.  
Standard Mode: best choice for document editing with SPLENDID™  
Video Enhancement.  
Theater Mode: best choice for movie with SPLENDID™ Video  
Enhancement.  
Game Mode: best choice for game playing with SPLENDID™ Video  
Enhancement.  
Night View Mode: best choice for dark-scene game or movie with  
SPLENDID™ Video Enhancement.  
In the Standard Mode, the Satuation and Sharpness functions are not user-  
configurable.  
In the other modes, the sRGB function is not user-configurable.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
3-1  
 
2.  
Image  
You can adjust brightness, contrast,  
sharpness, saturation, position (VGA only),  
ASCR, and focus (VGA only) from this  
main function.  
Brightness: the adjusting range is  
from 0 to 100. is a hotkey to  
activate this function.  
Contrast: the adjusting range is from  
0 to 100.  
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.  
Sharpness: the adjusting range is from 0 to 100.  
Saturation: the adjusting range is from 0 to 100.  
Position: adjusts the horizontal postition (H-Position) and the vertical  
position (V-Position) of the image. The adjusting range is from 0 to 100.  
Focus: reduces Horizonal-line noise and Vertical-line noise of the image  
by adjusting (Phase) and (Clock) separately. The adjusting range is from  
0 to 100.  
Phase adjusts the phase of the pixel clock signal. With a wrong phase  
adjustment, the screen shows horizontal disturbances.  
Clock (pixel frequency) controls the number of pixels scanned by one  
horizontal sweep. If the frequency is not correct, the screen shows vertical  
stripes and the image is not proportional.  
3.  
Color  
Select the image color you like from this  
function.  
Color Temp.: contains five color  
modes including Cool, Normal, Warm,  
sRGB, and User mode.  
Skin Tone: contains three color  
modes including Reddish, Natural,  
and Yellowish.  
In the User mode, colors of R (Red), G (Green), and B (Blue) are user-  
configurable; the adjusting range is from 0-100.  
3-2  
Chapter 3: General Instruction  
4.  
Input Select  
In this function, you can select either  
VGA or DVI input source. (Only for some  
models)  
5.  
System Setup  
Allow you to adjust the system.  
Volume: the adjusting range is from 0  
to 100.  
is a hotkey to activate this  
function.  
OSD Setup:  
* Adjusts the horizontal postition  
(H-Position)/ the vertical position  
(V-Position) of the OSD from 0 to 100.  
* Adjusts the OSD timeout from 10 to 120.  
* Enables or disables the DDC/CI function.  
Language: there are ten languages for your selection, including English,  
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,  
Simplified Chinese, and Japanese.  
Aspect Control: adjusts the aspect ratio to “Full” or “4:3”.  
Information: shows the monitor information.  
Reset: “Yes” allows you to restore the default setting.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
3-3  
3.2  
Specifications summary (VW195xL  
Series)  
Panel Type  
Panel size  
TFT LCD  
19" (16:10) wide screen  
Max. Resolution  
Pixel pitch  
WXGA+ 1440 x 900  
0.285mm  
250cd/m2  
300cd/m2  
Brightness (Typ.)  
Brightness (Max.)  
Contrast Ratio (Typ.)  
Contrast Ratio (Max.)  
Viewing angle(H/V) CR>10  
Display colors  
800:1  
2000:1 (with ASCR ON)  
160˚/160˚  
16.7M  
Response time  
5ms  
SPLENDID™ Video  
Enhancement  
Yes  
SPLENDID™ selection  
Auto adjustment  
Color temperature selection  
Skin-Tone selection  
Digital input  
5 video preset modes (by hotkey)  
Yes (by hotkey)  
5 color temperatures  
3 skin-tones  
DVI-D with HDCP (VW195TL / VW195NL)  
Analog input  
D-Sub  
Audio-in port  
3.5 mm Mini-jack (VW195TL / VW195SL)  
Colors  
Black  
Speaker (Built-in)  
Power LED  
1W x 2 Stereo, RMS (VW195TL / VW195SL)  
Blue (On) / Amber (Standby)  
VESA wall mount  
Tilt  
100 x 100mm  
-5˚~+20˚  
Swivel  
-45˚~+45˚  
Height adjustment  
Kensington lock  
Voltage rating  
Power consumption  
70mm  
Yes  
AC: 100~240V  
Power On : < 47W, Standby: < 2W, Power Off: <1W  
Temperature (Operating)  
0˚C~40˚C  
Temperature  
(Non-operating)  
-20˚C~+60˚C  
444 mm x 376 mm x 214 mm (machine)  
516 mm x 456 mm x 175 mm (package)  
4.2 kg (Net) ; 6.5 kg (Gross)  
Dimension (W x H x D)  
Weight (Esti.)  
10 languages (English, German, Italian, French, Dutch,  
Spanish, Russian, Traditional Chinese, Simplified  
Chinese, Japanese)  
Multi-languages  
VGA cable, DVI cable, audio cable, power cord, quick  
start guide, warranty card  
Accessories  
Energy Star®, CB, CE, Gost-R, CCC, UL, FCC, C-Tick,  
Regulation approvals  
BSMI, VCCI, TCO03, RoHS, WEEE, PSB  
*Specifications are subject to change without notice.  
3-4  
Chapter 3: General Instruction  
 
Specifications summary (VW202xL Series)  
Panel Type  
TFT LCD  
Panel size  
20.1" wide screen  
WSXGA+ 1680 x 1050  
0.258mm  
Max. Resolution  
Pixel pitch  
250cd/m2  
300cd/m2  
Brightness (Typ.)  
Brightness (Max.)  
Contrast Ratio (Typ.)  
Contrast Ratio (Max.)  
Viewing angle(H/V) CR>10  
Display colors  
1000:1  
3000:1 (with ASCR ON)  
160˚/160˚  
16.7M  
Response time  
5ms  
SPLENDID™ Video  
Enhancement  
Yes  
SPLENDID™ selection  
Auto adjustment  
Color temperature selection  
Skin-Tone selection  
Digital input  
5 video preset modes (by hotkey)  
Yes (by hotkey)  
5 color temperatures  
3 skin-tones  
DVI-D with HDCP (VW202TL / VW202NL)  
Analog input  
D-Sub  
USB 2.0 PC input  
Audio-in port  
VW202BL only  
3.5 mm Mini-jack (VW202TL / VW202SL)  
Colors  
Black  
Speaker (Built-in)  
Power LED  
1W x 2 Stereo, RMS (VW202TL / VW202SL)  
Blue (On) / Amber (Standby)  
VESA wall mount  
Tilt  
100 x 100mm  
-5˚~+20˚  
Swivel  
-45˚~+45˚  
Height adjustment  
Kensington lock  
Voltage rating  
Power consumption  
70mm  
Yes  
AC: 100~240V  
Power On : < 49W, Standby: < 2W, Power Off: <1W  
Temperature (Operating)  
0˚C~40˚C  
Temperature  
(Non-operating)  
-20˚C~+60˚C  
479 mm x 392 mm x 214 mm (machine)  
550 mm x 480 mm x 175 mm (package)  
4.4 kg (Net) ; 6.8 kg (Gross)  
Dimension (W x H x D)  
Weight (Esti.)  
10 languages (English, German, Italian, French, Dutch,  
Spanish, Russian, Traditional Chinese, Simplified  
Chinese, Japanese)  
Multi-languages  
VGA cable, DVI cable, audio cable, USB cable  
(VW202BL only), power cord, quick start guide, warranty  
card  
Accessories  
Energy Star®, CB, CE, Gost-R, CCC, CSA, FCC, C-Tick,  
Regulation approvals  
BSMI, VCCI, TCO03, RoHS, WEEE, PSB  
*Specifications are subject to change without notice.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
3-5  
Specifications summary (VW225xL Series)  
Panel Type  
TFT LCD  
Panel size  
22.0" (16:10) wide screen  
WSXGA+ 1680 x 1050  
0.282mm  
Max. Resolution  
Pixel pitch  
250cd/m2  
300cd/m2  
Brightness (Typ.)  
Brightness (Max.)  
Contrast Ratio (Typ.)  
Contrast Ratio (Max.)  
Viewing angle(H/V) CR>10  
Display colors  
1000:1  
8000:1 (with ASCR ON)  
170˚/160˚  
16.7M  
Response time  
5ms  
SPLENDID™ Video  
Enhancement  
Yes  
SPLENDID™ selection  
Auto adjustment  
Color temperature selection  
Skin-Tone selection  
Digital input  
5 video preset modes (by hotkey)  
Yes (by hotkey)  
5 color temperatures  
3 skin-tones  
DVI-D with HDCP (VW225TL / VW225NL)  
Analog input  
D-Sub  
Audio-in port  
3.5 mm Mini-jack (VW225TL / VW225SL)  
Colors  
Black  
Speaker (Built-in)  
Power LED  
1W x 2 Stereo, RMS (VW225TL / VW225SL)  
Blue (On) / Amber (Standby)  
VESA wall mount  
Tilt  
100 x 100mm  
-5˚~+20˚  
Swivel  
-45˚~+45˚  
Height adjustment  
Kensington lock  
Voltage rating  
Power consumption  
70mm  
Yes  
AC: 100~240V  
Power On : < 55W, Standby: < 2W, Power Off: <1W  
Temperature (Operating)  
0˚C~40˚C  
Temperature  
(Non-operating)  
-20˚C~+60˚C  
513 mm x 405 mm x 214 mm (machine)  
601 mm x 487 mm x 175 mm (package)  
5.0 kg (Net) ; 7.6 kg (Gross)  
Dimension (W x H x D)  
Weight (Esti.)  
10 languages (English, German, Italian, French, Dutch,  
Spanish, Russian, Traditional Chinese, Simplified  
Chinese, Japanese)  
Multi-languages  
VGA cable, DVI cable, audio cable, power cord, quick  
start guide, warranty card  
Accessories  
Energy Star®, CB, CE, Gost-R, CCC, UL, FCC, C-Tick,  
Regulation approvals  
BSMI, VCCI, TCO03, RoHS, WEEE, PSB  
*Specifications are subject to change without notice.  
3-6  
Chapter 3: General Instruction  
3.3  
Troubleshooting (FAQ)  
Problem  
Possible Solution  
Power LED is not ON  
• Press the  
button to check if the monitor  
is in the ON mode.  
• Check if the power cord is properly  
connected to the monitor and the power  
outlet.  
The power LED lights amber and there is no • Check if the monitor and the computer are  
screen image  
in the ON mode.  
• Make sure the signal cable is properly  
connected the monitor and the computer.  
• Inspect the signal cable and make sure  
none of the pins are bent.  
• Connect the computer with another  
available monitor to check if the computer  
is properly working.  
Screen image is too light or dark  
• Adjust the Contrast and Brightness settings  
via OSD.  
Screen image is not centered or sized  
• Press the  
button for two seconds to  
properly  
automatically adjust the image.  
• Adjust the H-Position or V-Position settings  
via OSD.  
Screen image bounces or a wave pattern is • Make sure the signal cable is properly  
present in the image  
connected to the monitor and the computer.  
• Move electrical devices that may cause  
electrical interference.  
Screen image has color defects (white does • Inspect the signal cable and make sure that  
not look white)  
none of the pins are bent.  
• Perform Reset via OSD.  
• Adjust the R/G/B color settings or select the  
Color Temperature via OSD.  
Screen image is blurry or fuzzy  
• Press the  
button for two seconds to  
automatically adjust the image (for VGA  
mode only).  
• Adjust the Phase and Clock settings via  
OSD.  
No sound or sound is low  
• Ensure that the audio cable is properly  
connected to the monitor and the computer  
• Adjust the volume settings of both your  
monitor and computer.  
• Ensure that the computer sound card driver  
is properly installed and activated.  
ASUS VW195xL/VW202xL/VW225xL Series LCD Monitor  
3-7  
 
3.4  
Standard  
DOS  
Supported operating modes  
Resolution  
Frequency  
Horizontal  
Frequency  
Vertical  
Frequency  
Pixel  
720 x 400  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 960  
1280 x 1024  
1280 x 1024  
1152 x 864  
31.47KHz  
31.47KHz  
37.90KHz  
37.50KHz  
35.16KHz  
37.90KHz  
48.10KHz  
46.90KHz  
48.40KHz  
56.50KHz  
60.02KHz  
60.00KHz  
64.00KHz  
80.00KHz  
67.50KHz  
70Hz  
60Hz  
72Hz  
75Hz  
56Hz  
60Hz  
72Hz  
75Hz  
60Hz  
70Hz  
75Hz  
60Hz  
60Hz  
75Hz  
75Hz  
28.32MHz  
25.18MHz  
31.50MHz  
31.50MHz  
36.00MHz  
40.00MHz  
50.00MHz  
49.50MHz  
65.00MHz  
75.00MHz  
78.75MHz  
108.00MHz  
108.00MHz  
135.00MHz  
108.00MHz  
VGA  
SVGA  
XGA  
SXGA  
VESA  
UXGA  
VESA  
1440 x 900  
(VW195xL Primary)  
55.94KHz  
75.00KHz  
60Hz  
60Hz  
106.5MHz  
1600 x 1200  
1680 x 1050  
(VW202xL / VW225xL 65.29KHz  
162.00MHz  
60Hz  
146.25MHz  
Primary)  
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that  
you choose a mode listed in the table above.  
3-8  
Chapter 3: General Instruction  
 

Hotpoint C150 User Manual
Frigidaire 318201451 User Manual
Dynex DX R20TV User Manual
Dell UltraSharp 1800FP User Manual
Cypress CY7C292A User Manual
Crestron electronic Crestron Electronics Computer Hardware CP2E User Manual
Cisco Systems 30 VIP User Manual
Asus M2R FVM User Manual
Asus Graphics Card GTX760DC2OC2GD5 User Manual
Analog Devices ADuC812 User Manual